Car Key Button Repair
A damaged car key button can be frustrating. You may need to contact the 24 hour Locksmith Service or purchase a replacement remote.
You may be able save money by fixing your old key fob instead of replacing it. This is particularly true if the issue is caused by the worn-out switch or defective contact.
Battery
If your key fob's buttons do not respond when you pressing them, this could be a sign that the battery has failed or is about to reach the end of life. Fortunately, replacing the battery is an easy task that you can complete on your own rather than paying a locksmith or dealership to complete the task for you.
First find the battery compartment. It is usually located on the back of the key fob and might be hidden behind a slide-out cover or an access point which opens when you press a button. After the compartment is exposed then look for the small button-cell battery. This is typically shaped like coins and has an minus and plus sign. Take the old battery out, and replace it with a new one. Make sure the plus and minus symbols are aligned correctly.
Close the compartment and snap the two parts of your key fob. Before closing the door make sure to align and snap the components into place. Press any of the buttons to confirm that they work properly.
If your remote key fob stops functioning even after replacing the battery, it could be experiencing other issues that require a different type of repair. The fob's dropping in a puddle could cause it to stop functioning. It could also be suffering from an electrical issue within the device or may need to be deprogrammed by a locksmith or locksmith. Also, take a look at these common auto troubleshooting techniques to determine whether your key fob may be suffering from a different issue.
Switches
Based on the year and make, there are different kinds of switches that are found on the car keyfob. The older model of key often has a separate chip that you can see in the case, whereas modern keys are more sophisticated and function by sending signals to the car. Whatever the model of key, the keys' buttons can become worn out or damaged during normal use. car key repairs become difficult to press or unresponsive. If you press the button with force it could cause more damage. It could also stop the key from functioning in the future.
If your key doesn't seem to be working, first try changing the battery. If that doesn't help then you might need to clean your key fob and re-adjust the switches. Since these tiny electronic switches are constantly being tossed around, they are more likely to wear out than larger components of your key.
The switches feel rubbery and are coated with a film that conducts electricity. The film may fade over time. However, they're small and inexpensive to replace. They are soldered onto the circuit board, therefore it is important to remove the old ones without causing any damage to any other part of the circuit. Then you can solder the new ones in and put them back together.
An effective way to protect your car key fob from being damaged is to not use it for more than a few hours at a time and to keep it out of the way in places that it will be visible. Also, you should locate a safe place to store your key when you're not making use of it.
If the issue persists after you've cleaned your key fob or battery, and tried to clean it, then you might need to contact an expert locksmith. A professional locksmith can test the frequency of your key to determine if it's still able to communicate with your vehicle, and open and replace micro switches, change cases and more.
Outer Case
Key fobs spend many hours bouncing around, and when the buttons aren't allowed to move between the case, they could become stuck or even broken. If changing the battery or cleaning with a cotton swab and some alcohol rubbing doesn't solve the problem, removing the case and inspecting could be required. If the contact points where the buttons touch don't fit well or are worn out, adjusting them may be the only way to correct the issue.
Rubber buttons may get worn out over time. Rubber buttons can become hard to press when they stretch, and nails could gouge them. In this case, the key may fail, and it's time to replace the case or the buttons. This repair involves removing the remote, then locating the buttons on the circuit board, and then heating the solder before carefully taking them off. The circuit board is then soldered with new buttons. The case can then be rebuilt with the horse shoe key blade piece inserted. The new buttons should be snugly fitted into the case to prevent them from falling out.
car key repair
Since your key fob is prone to be tossed around and could occasionally be pressed by accident and the buttons within can become stuck or broken over time. With the help of metallic tape and a hole punch you can often quickly fix this problem when your car is not at home and the key fob isn't working and allows you to open the doors, but not to start the engine. This simple fix can allow you to safely return to your vehicle to complete your journey.